Articles
  • Mechanical properties of PLA and ABS parts produced with fused filament fabrication method

  • İsmail Topcu*

  • Department of Metallurgy and Materials Engineering, Alanya Alaaddin Keykubat University, Antalya, Turkey

  • This article is an open access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

References
  • 1. B. Brenken, E. Barocio, A. Favaloro, V. Kunc, V. and R.B. Pipes, Additive Manufacturing 21 (2018) 1-16.
  •  
  • 2. M. Asadi, B. Bazyar, A.H. Hemmasi, L. Ghsemi, and M. Talaeipoor, Tehnički Glasnik 69[2] (2018) 127-134.
  •  
  • 3. J.P. Kruth, L. Froyen, J.V. Vaerenbergh, P. Mercelis, M. Rombouts and B. Lauwers, J. Mater. Process. Technol. 149[1] (2004) 616-622.
  •  
  • 4. L.E. Murr, M.S. Gaytan, D.A. Ramirez, E.Martinez, J. Hernandez, N.A. Amato, P.W. Shindo, F.R. Medina and B. Ryan and R.B. Wicker, J. Mater. Sci. Technol. 28[1] (2012) 1-14.
  •  
  • 5. M.V. Fernandez, W. Calle, S. Ferrandiz, and A. Conejero, 3D Print. Addit. Manuf. 3[3] (2016) 183-192.
  •  
  • 6. Q. Sun, R. Qattawi, C.T. Bellehumeur and P. Gu, Rapid Prototyping J. 14[2] (2008) 72-80.
  •  
  • 7. M. Asadi, B. Bazyar, A.H. Hemmasi, I. Ghsemi and M. Talaeipoor, Tehnički Glasnik 69[2] (2018) 127-134,
  •  
  • 8. F. Melchels, J. Feijen and D.W. Grijpma, Biomaterials 31[24] (2010) 6121-6130.
  •  
  • 9. M. Singh, H.M. Haverinen, P. Dhagat and G.E. Jabbour, Adv. Mater 22[6] (2010) 673-685.
  •  
  • 10. J. Park, M.J. Tari and H.T Hahn, Rapid Prototyping J. 6[1] (2000) 36-49
  •  
  • 11. R.J. Allen and R.S. Trask, Additive Manufacturing 8 (2015) 78-87.
  •  
  • 12. N.G. Tanikella, B. Wittbrodt and J.M. Pearce, Additive Manufacturing 15 (2017) 40-47.
  •  
  • 13. M. Á. Caminero, J. M. Chacón, E. G.Plaza, P.J. Núñez, J. M. Reverte and J.P. Becar, Polymer 11 (2019) 1-22
  •  
  • 14. A. Lanzotti, M. Grasso, G. Staiano and M. Martorelli, Rapid Prototyping J. 21[5] (2015) 604-617.
  •  
  • 15. F. Ning, W. Cong, J. Qiu, J. Wei and S. Wang, Composites, Part B 80 (2015) 369-378.
  •  
  • 16. İ. Topcu, B.N. Çetiner, A.N. Güllüoglu, H.Ö. Gülsoy, J. Chem. Soc. Pak. 42 (2020) 70-80.
  •  
  • 17. İ. Topcu, A.N. Güllüoglu, M.K. Bilici, H.Ö. Gülsoy, Journal of the Faculty of Engineering and Architecture of Gazi University 34 (2019) 141-149
  •  
  • 18. M. Montero, S. Roundy, D. Odell, S.H. Ahn and P.K. Wright, Soc. Manuf. Eng. 8[4] (2001) 248-257.
  •  
  • 19. J.M. Chacón, M.Á. Caminero, E.G. Plaza, and P.J.N. Lopez, Mater. Des. 124 (2017) 143-157.
  •  
  • 20. İ. Topcu, H.Ö. Gülsoy, A.N. Güllüoglu, Gazi University Journal of Science 32 (2019) 286-298
  •  
  • 21. X. Wang, P. Wei, R. Han, W. Xie, T. Li, D. Li, Y. Ganb, Z. Chen and F. Xing, J. Ceram. Process. Res. 20[s1] (2019) 19-30.
  •  
  • 22. M. Ravindran, S. Senthil Kumar, N. Karuppiah and M. Asokan, J. Ceram. Process. Res. 21[1] (2020) 14-20.
  •  
  • 23. A. Rehmana, J. B. Leeb, A. Qudoosa, S. H. Jakhrania, H. G. Kima and J.S. Ryoua, J. Ceram. Process. Res. 20[3] (2019) 270-275
  •  

This Article

  • 2021; 22(2): 143-148

    Published on Apr 30, 2021

  • 10.36410/jcpr.2021.22.2.143
  • Received on Mar 30, 2020
  • Revised on May 27, 2020
  • Accepted on Jun 10, 2020

Correspondence to

  • İsmail Topcu

  • Department of Metallurgy and Materials Engineering, Alanya Alaaddin Keykubat University, Antalya, Turkey
    Tel : + 90 242 510 61 20 Fax: + 90 242 510 61 24

  • E-mail: ismail.topcu@alanya.edu.tr